Suitable for lifting, pressurizing, and distributing in civil and industrial installations, distribution to autoclaves and cisterns, washing systems, irrigation systems, with transfer from wells with a minimum diameter of 310 mm, irrigation systems, tanks, and basins.

Series

SP-302

Characteristics

Shaft: Stainless steel Aisi-431
Impeller: Cast iron EN-GJL-250
Diffuser: Cast iron EN-GJL-250
Suction support: Cast iron EN-GJS-500/7
Discharge nozzle with check valve: Cast iron EN-GJS-500/7
Solid passage [mm]: 3
Fluid temperature (ºC): 0-30º
Max. operating pressure (bar): 39
Max. immersion depth [m]: 300
Rotation direction: Clockwise, viewed from the discharge nozzle
Q max. [m³/h]: 575
H max. [m³/h]: 384

Submersible electric pumps suitable for draining clear and turbid water. Ideal for use in construction sites, even for pumping abrasive liquids.

Series

TEX-D

Features

– Pump body: EN-GJL-250 cast iron
– Diffuser: EN-GJL-250 cast iron
– Impeller: Brass
– Rotor shaft: Stainless steel Aisi-431
– Mechanical seal on pump side: Silicon/Ceramic
– Mechanical seal on motor side: Carbon/Ceramic
– Max flow rate [m³/h]: 39
– Max head [m]: 18

Monobloc gear electric pumps. They are suitable for pumping oils, dense and viscous fluids (mineral oils, etc.), glues, paints, molasses, soaps, or greases.

Series

CFP / CF

Characteristics

– Body: Cast iron
– Gears: One gear in steel and the other in bronze.
– Seal: With radial rubber rings.
– Motor protection: IP 44 | IP 55 (On demand)
– Standard voltage: 1x230V / 3x230V/400V
– Max flow rate [m³/h]: 1.2
– Max head [m]: 140
– Max fluid temperature [ºC]: -15/+60
– Max ambient temperature [ºC]: 40
– By-pass adjustment: 8 bar (CFP) -10 bar (CF)
– Max suction [m]: 8

Submersible electric pumps specially designed for pumping water with suspended solids, unfiltered groundwater, rainwater, and wastewater free of long fibers. They are also designed to pump liquids from livestock farming as well as industrial discharges, as long as they are chemically compatible with the construction materials of the electric pump.

Series

SD

Characteristics

– Pump body: Cast iron EN-GJL-200
– Motor unit: Cast iron EN-GJL-200 (motor isolated in a dry chamber)
– Impeller: Cast iron EN-GJL-250
– Insulation: Class H
– Protection grade: IP 68
– Standard voltage: 3x400V at 50 Hz
– Protection kit with PTC probe and water detection in the oil chamber.
– Motor efficiency: 93.6%
– Max fluid temperature [ºC]: -15 / +40

Rewindable motors in water bath with PVC or PE+PA winding for operation in 10″ or larger wells with radial or semi-axial submersible pumps.

Series

MS-251

Features

– Coupling flange to the pump according to NEMA 10″ standards.
– Compensation membrane.
– Bidirectional axial bearing type Kingsbury.
– Radial bearings lubricated by water.
– Double sealing system on the shaft side.
– 4-meter cable in its standard version according to drinking water standards.
– 100% of the motors are tested. Test certificate provided upon request.
– Suitable for operation with frequency converter.
– Protection grade: IP68.
– Shaft: Stainless steel Aisi-431.
– Sleeve: Stainless steel Aisi-304.
– Rotation direction: No distinction.
– Max fluid temperature [ºC]: 25 in PVC / 50 in PE.
– Axial load [N]: 60000.

Special Versions

– PE winding for hot water up to 50ºC.
– Version for horizontal operation up to 170 kW.
– MSX: Version in stainless steel AISI-316.
– MSB: Bronze version.
– Special mechanical seals upon request.
– Cables in different lengths.

Water bath winding motors with PVC or PE windings for operation in 12″ tanks or higher with radial or semi-axial submersible pumps.

Series

MS-300

Features

– Coupling flange on the pump according to NEMA 12″ standards.
– Compensating diaphragm
– Kingsbury type bidirectional thrust bearing
– Water lubricated radial bearings
– Double locking on the shaft side
– 4 meter cable in the standard version according to drinking water standard.
– 100% of the motors are tested. Test certificate available on request.
– They are suitable for operation with frequency variator.
– Protection class: IP68
– Shaft: stainless steel. Aisi-431
– Shirt: stainless steel. Aisi-304
– Max. Fluid temperature [ºC]: 25
– Axial load[N]: 7000000

Special Version
– PE winding for hot water up to 50ºC
– Version for horizontal operation up to 170 kW
– MSX: stainless steel version AISI-316
– MSB: Bronze version
– Special mechanical seals under control
– Cable in different lengths

Rewindable oil-filled motors for operation in 4″ or larger wells with radial or semi-axial submersible pumps, constructed in AISI-304 stainless steel.

Series

CLX-95 / CLEX-95

Characteristics

– Pump coupling flange according to NEMA 4″ standards.
– Compensation membrane
– Multiple sealing system on the shaft side
– Single-phase motors are of the PSC (Permanent Split Capacitor) type with a capacitor always connected. The capacitor is supplied separately.
– Rotation direction: Counterclockwise in single-phase motors viewed from the top of the shaft. In three-phase motors, there is no distinction between clockwise or counterclockwise.
– Cable compliant with drinking water standards
– 100% of the motors are tested. Test certificate provided upon request.
– Suitable for operation with a frequency converter.
– Shaft: Stainless steel Aisi-431
– Casing: Stainless steel Aisi-304
– Max. fluid temperature [ºC]: CL-95: 35 / CLE-95: 25
– Axial load [N]: CL-95: 3000 (0.37-2.2 kW) – 6500 (3-7.5 kW) / CLE-95: 3000 (0.37-2.2 kW)

Special Versions

– CLXV: Coupling flange in stainless steel Aisi-316

Motors in water bath rewindable with PVC or PE winding for operation in 6” or larger wells with radial or semi-axial submersible pumps.

Series

MS-152

Features

– Coupling flange to the pump according to NEMA 6” standards.
– Compensation membrane.
– Bidirectional axial bearing type Kingsbury.
– Radial bearings lubricated by water.
– Double sealing system on the shaft side.
– 3-meter cable in its standard version according to drinking water standards.
– 100% of the motors are tested. Test certificate provided upon request.
– Suitable for operation with frequency converter.
– Protection grade: IP68.
– Shaft: Stainless steel Aisi-431.
– Sleeve: Stainless steel Aisi-304.
– Rotation direction: No distinction.
– Max fluid temperature [ºC]: 25 in PVC / 50 in PE.
– Axial load [N]: 10000 (1.5 – 13 kW) – 17700 (15 – 26 kW).

Special Versions

– Coupling flange to the pump NEMA 4”.
– PE+PA winding for hot water up to 50ºC.
– Version for horizontal operation up to 30 kW.
– MSX: Version in stainless steel AISI-316.
– MSB: Bronze version.
– Special mechanical seals upon request.
– Cables in different lengths.

Motors in water bath rewindable with PVC or PE winding for operation in 8″ or larger wells with radial or semi-axial submersible pumps.

Series

MS-201

Features

– Coupling flange to the pump according to NEMA 8″ standards.
– Compensation membrane.
– Bidirectional axial bearing type Kingsbury.
– Radial bearings lubricated by water.
– Double sealing system on the shaft side.
– 4-meter cable in its standard version according to drinking water standards.
– 100% of the motors are tested. Test certificate provided upon request.
– Suitable for operation with frequency converter.
– Max fluid temperature [ºC]: 25 in PVC / 50 in PE.
– Protection grade: IP68.
– Shaft: Stainless steel Aisi-431.
– Sleeve: Stainless steel Aisi-30.
– Rotation direction: No distinction.
– Axial load [N]: 22050 (13 – 37 kW) – 45000 (45 – 110 kW).

Special Versions

– Coupling flange to the pump NEMA 6″.
– PE winding for hot water up to 50ºC.
– Version for horizontal operation up to 92 kW.
– MSX: Version in stainless steel AISI-316.
– MSB: Bronze version.
– Special mechanical seals upon request.
– Cables in different lengths.

Suitable for lifting, pressurizing, and distributing in civil and industrial installations, distribution to autoclaves and tanks, washing systems, irrigation systems, with transfer from wells with a minimum diameter of 156 mm, tanks, and basins.

Series

RP-152

Characteristics

Shaft: Stainless steel Aisi-431
Impeller: Polycarbonate (On demand in brass)
Diffuser: Polycarbonate
Suction support: Cast iron (On demand in stainless steel Aisi-304)
Discharge port: Cast iron (On demand in stainless steel Aisi-304)
Pump body and cable cover: Stainless steel Aisi-304
Valve: Stainless steel Aisi-304 with polycarbonate
Solid passage [mm]: 4
Fluid temperature [ºC]: 0-35º
Max operating pressure (bar): 54
Max immersion depth [m]: 300
Rotation direction: Counterclockwise, viewed from the discharge port
Max flow rate [m3/h]: 64
Max height [m]: 540